Part Number Hot Search : 
2SD88 S10ML1X HD68B45R PDB0805 GRM32ER UNRF2AM SMLJ130 331M25
Product Description
Full Text Search
 

To Download EL2074CS-T7 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  note : all information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publi cation; however, this data sheet cannot be a ?controlled document?. current revisions, if any, to these specifications are maintained at the factory and are available upon your request. we recommend checking the revision level befor e finalization of your design documentation. ? 2001 elantec semiconductor, inc. e l 2 0 7 4 c general description the el2074c is a precision voltage-feedback amplifier featuring a 400mhz gain-bandwidth product, fast settling time, excellent differ- ential gain and differential phase performance, and a minimum of 50ma output current drive over temperature. the el2074c is gain-of-2 stable with a -3db bandwidth of 400mhz at a v = +2. it has a very low 200v of input offset voltage, only 2a of input bias current, and a fully symmetrical differential input. like all voltage-feedback operational amplifiers, the el2074c allows the use of reactive or non-linear components in the feedback loop. this combination of speed and versatility makes the el2074c the ideal choice for all op-amp applications at a noise gain of 2 or greater requiring high speed and precision, including active filters, integra- tors, sample-and-holds, and log amps. the low distortion, high output current, and fast settling makes the el2074c an ideal amplifier for signal-processing and digitizing systems. connection diagram 1 2 3 4 8 7 6 5 el2074c (8-pin so & 8-pin pdip) nc in- in+ v- nc v+ out nc - + features ? 400mhz gain-bandwidth product ? gain-of-2 stable ? ultra low video distortion = 0.01%/0.015 @ntsc/pal ? conventional voltage-feedback topology ? low offset voltage = 200v ? low bias current = 2a ? low offset current = 0.1a ? output current = 50ma over temperature ? fast settling = 13ns to 0.1% ? low distortion = -55db hd2, ------ -70db hd3 @20mhz, 2v pp , a v = +2 applications ? high resolution video ? active filters/integrators ? high-speed signal processing ? adc/dac buffers ? pulse/rf amplifiers ? pin diode receivers ? log amplifiers ? photo multiplier amplifiers ? high speed sample-and-holds ordering information part no. package tape & reel outline # el2074cn 8-pin pdip - mdp0031 el2074cs 8-pin so - mdp0027 EL2074CS-T7 8-pin so 7? mdp0027 el2074cs-t13 8-pin so 13? mdp0027 el2074c 400mhz gbwp gain-of-2 stable operational amplifier s e p t e m b e r 2 6 , 2 0 0 1
2 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c absolute maximum ratings (t a = 25c) supply voltage (v s ) 7v output current output is short-circuit protected to ground, however, maximum reliability is obtained if i out does not exceed 70ma. common-mode input v s differential input voltage 5v thermal resistance (pdip) q ja = 95c/w thermal resistance (so) q ja = 175c/w operating temperature 0c to +75c junction temperature 175c storage temperature -60c to +150c note: see el2071/el2171 for thermal impedance curves important note: all parameters having min/max specifications are guaranteed. typ values are for information purposes only. unless otherwise note d, all tests are at the specified temperature and are pulsed tests, therefore: t j = t c = t a . open loop dc electrical characteristics v s = 5v, r l = 100 w , unless otherwise specified. parameter description test conditions temp min typ max unit v os input offset voltage v cm = 0v 25c 0.2 1.5 mv t min , t max 3 mv tcv os average offset voltage drift [1] all 8 v/c i b input bias current v cm = 0v all 2 6 a i os input offset current v cm = 0v 25c 0.1 1 a t min , t max 2 a psrr power supply rejection ratio [2] all 60 80 db cmrr common mode rejection ratio [3] all 65 90 db i s supply current - quiescent no load 25c 21 25 ma t min , t max 25 ma r in (diff) r in (differential) open-loop 25c 15 k w c in (diff) c in (differential) open-loop 25c 1 pf r in (cm) r in (common-mode) 25c 1 m w c in (cm) c in (common-mode) 25c 1 pf r out output resistance 25c 20 m w cmir common-mode input range 25c 3 3.5 v t min , t max 2.5 v i out output current all 50 70 ma v out output voltage swing no load all 3.5 4 v v out 100 output voltage swing 100 w all 3 3.6 v v out 50 output voltage swing 50 w all 2.5 3.4 v a vol 100 open-loop gain 100 w 25c 500 1000 v/v t min , t max 400 v/v a vol 50 open-loop gain 50 w 25c 400 800 v/v t min , t max 300 v/v en@ > 1mhz noise voltage 1mhz to 100mhz 25c 2.3 nv/ ? hz in@ > 100khz noise current 100khz to 100mhz 25c 3.2 pa/ ? hz 1. measured from t min , t max 2. v cc = 4.5v to 5.5v 3. v in = 2.5v, v out = 0v
3 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c closed loop ac electrical characteristics v s = 5v, a v = +2, r f = r g = 250 w , c f = 3pf, r l = 100 w unless otherwise specified. parameter description test conditions temp min typ max unit ssbw -3db bandwidth a v = -1 25c 400 mhz (v out = 0.4v pp ) a v = +2 25c 250 400 mhz t min , t max 250 mhz a v = +5 25c 100 mhz a v = +10 25c 40 mhz gbwp gain-bandwidth product a v = +10 25c 400 mhz lsbwa -3db bandwidth v out = 2v pp [1] all 43 63 mhz lsbwb -3db bandwidth v out = 5v pp [1] all 17 25 mhz gfpl peaking (<50mhz) v out = 0.4v pp 25c 0 1 db t min , t max 1 db gfph peaking (>50mhz) v out = 0.4v pp 25c 0 2 db t min , t max 2 db gfr rolloff (<100mhz) v out = 0.4v pp 25c 0.1 0.5 db t min , t max 0.5 db lpd linear phase deviation (<100mhz) v out = 0.4v pp all 1 1.8 pm phase margin a v = +2 25c 50 tr1, tf1 rise time, fall time 0.4v step, a v = +2 25c 1.8 ns tr2, tf2 rise time, fall time 5v step, a v = +2 25c 8 ns ts1 settling to 0.1% (a v = -1) 2v step 25c 13 ns ts2 settling to 0.01% (a v = -1) 2v step 25c 25 ns os overshoot 2v step 25c 5 % sr slew rate 2v step all 275 400 v/s distortion [2] hd2a 2nd harmonic distortion @ 10mhz, a v = +2 25c -65 -55 dbc hd2c 2nd harmonic distortion @ 20mhz, a v = +2 25c -55 -45 dbc t min , t max -45 dbc hd3a 3rd harmonic distortion @ 10mhz, a v = +2 25c -72 -60 dbc hd3c 3rd harmonic distortion @ 20mhz, a v = +2 25c -70 -60 dbc t min , t max -60 dbc video performance [3] dg differential gain ntsc 25c 0.01 0.05 % pp dp differential phase ntsc 25c 0.015 0.05 pp dg differential gain 30mhz 25c 0.1 % pp dp differential phase 30mhz 25c 0.1 pp vbw 0.1 db bandwidth flatness 25c 25 50 mhz 1. large-signal bandwidth calculated using lsbw = slew rate / 2 p v peak 2. all distortion measurements are made with v out = 2v pp , r l = 100 w 3. video performance measured at a v = +2 with 2 times normal video level across r l = 100 w . this corresponds to standard video levels across a back- terminated 50 w load, i.e., 0?100 ire, 40irepp giving a 1v pp video signal across the 50 w load. for other values of r l , see curves
4 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c typical performance curves non-inverting frequency response inverting frequency response frequency response for various r l s open loop gain and phase output voltage swing vs frequency equivalent input noise psrr, cmrr, and closed-loop r o vs frequency 2nd and 3rd harmonic distortion vs frequency 2-tone, 3rd order intermodulation intercept
5 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c series resistor and resulting bandwidth vs capacitive load settling time vs output voltage change settling time vs closed-loop gain supply current vs temperature bias and offset current vs input common-mode voltage common-mode rejection ratio vs input common-mode voltage bias and offset current vs temperature offset voltage vs temperature a vol , psrr, and cmrr vs temperature
6 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c small signal transient response large signal transient response differential gain and phase vs dc input offset at 3.58mhz differential gain and phase vs dc input offset at 4.43mhz differential gain and phase vs dc input offset at 30mhz differential gain and phase vs number of 150 w loads at 3.58mhz differential gain and phase vs number of 150 w loads at 4.43mhz differential gain and phase vs number of 150 w loads at 30mhz
7 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c equivalent circuit burn-in circuit all packages use the same schematic
8 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c applications information product description the el2074c is a wideband monolithic operational amplifier built on a high-speed complementary bipolar process. the el2074c uses a classical voltage-feedback topology which allows it to be used in a variety of appli- cations requiring a noise gain 3 2 where current-feedback amplifiers are not appropriate because of restrictions placed upon the feedback element used with the ampli- fier. the conventional topology of the el2074c allows, for example, a capacitor to be placed in the feedback path, making it an excellent choice for applications such as active filters, sample-and-holds, or integrators. simi- larly, because of the ability to use diodes in the feedback network, the el2074c is an excellent choice for appli- cations such as log amplifiers. the el2074c also has excellent dc specifications: 200v, v os , 2a i b , 0.1a i os , and 90db of cmrr. these specifications allow the el2074c to be used in dc-sensitive applications such as difference amplifiers. furthermore, the current noise of the el2074c is only 3.2pa/ ? hz, making it an excellent choice for high-sen- sitivity transimpedance amplifier configurations. gain-bandwidth product the el2074c has a gain-bandwidth product of 400mhz. for gains greater than 8, its closed-loop -3db bandwidth is approximately equal to the gain-bandwidth product divided by the noise gain of the circuit. for gains less than 8, higher-order poles in the amplifier's transfer function contribute to even higher closed loop bandwidths. for example, the el2074c has a -3db bandwidth of 400mhz at a gain of +2, dropping to 200mhz at a gain of +4. it is important to note that the el2074c has been designed so that this ?extra? band- width in low-gain applications does not come at the expense of stability. as seen in the typical performance curves, the el2074c in a gain of +2 only exhibits 1db of peaking with a 100 w load. parasitic capacitances and stability when used in positive-gain configurations, the el2074c can be quite sensitive to parasitic capacitances at the inverting input, especially with values 3 250 w for the gain resistor. the problem stems from the feedback and gain resistance in conjunction with the approxi- mately 3pf of board-related parasitic capacitance from the inverting input to ground. assuming a gain-of-2 con- figuration with r f = r g = 250 w , a feedback pole occurs at 424mhz, which is equivalent to a zero in the forward path at the same frequency. this zero reduces stability by reducing the effective phase-margin from about 50 to about 30. a common solution to this problem is to add an addi- tional capacitor from the inverting input to the output. this capacitor, in conjunction with the parasitic capaci- tance, maintains a constant voltage-divider between the output and the inverting input. this technique is used for ac testing of the el2074. a 3pf capacitor is placed in parallel with the feedback resistor for all ac tests. when this capacitor is used, it is also possible to increase the resistance values of the feedback and gain resistors with- out loss of stability, resulting in less loading of the el2074c from the feedback network. video performance an industry-standard method of measuring the video distortion of a component such as the el2074c is to measure the amount of differential gain (dg) and differ- ential phase (dp) that it introduces. to make these measurements, a 0.286v pp (40 ire) signal is applied to the device with 0v dc offset (0 ire) at either 3.58mhz for ntsc, 4.43mhz for pal, or 30mhz for hdtv. a second measurement is then made at 0.714v dc offset (100 ire). differential gain is a measure of the change in amplitude of the sine wave, and is measured in per- cent. differential phase is a measure of the change in phase, and is measured in degrees. for signal transmission and distribution, a back-termi- nated cable (75 w in series at the drive end, and 75 w to ground at the receiving end) is preferred since the impedance match at both ends will absorb any reflec- tions. however, when double termination is used, the received signal is halved; therefore a gain of 2 configu- ration is typically used to compensate for the attenuation.
9 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c the el2074c has been designed to be among the best video amplifiers in the marketplace today. it has been thoroughly characterized for video performance in the topology described above, and the results have been included as minimum dg and dp specifications and as typical performance curves. in a gain of +2, driving 150 w , with standard video test levels at the input, the el2074c exhibits dg and dp of only 0.01% and 0.015 at ntsc and pal. because dg and dp vary with differ- ent dc offsets, the superior video performance of the el2074c has been characterized over the entire dc off- set range from -0.714v to +0.714v. for more information, refer to the curves of dg and dp vs dc input offset. the excellent output drive capability of the el2074c allows it to drive up to 4 back-terminated loads with excellent video performance. with 4 150 w loads, dg and dp are only 0.15% and 0.08 at ntsc and pal. for more information, refer to the curves for video perfor- mance vs number of 150 w loads. output drive capability the el2074c has been optimized to drive 50 w and 75 w loads. it can easily drive 6v pp into a 50 w load. this high output drive capability makes the el2074c an ideal choice for rf, if and video applications. furthermore, the current drive of the el2074c remains a minimum of 50ma at low temperatures. the el2074c is current- limited at the output, allowing it to withstand momen- tary shorts to ground. however, power dissipation with the output shorted can be in excess of the power-dissipa- tion capabilities of the package. capacitive loads although the el2074c has been optimized to drive resistive loads as low as 50 w , capacitive loads will decrease the amplifier's phase margin which may result in peaking, overshoot, and possible oscillation. for opti- mum ac performance, capacitive loads should be reduced as much as possible or isolated via a series out- put resistor. coax lines can be driven, as long as they are terminated with their characteristic impedance. when properly terminated, the capacitance of coaxial cable will not add to the capacitive load seen by the amplifier. capacitive loads greater than 10pf should be buffered with a series resistor (rs) to isolate the load capacitance from the amplifier output. a curve of recommended rs vs cload has been included for reference. values of rs were chosen to maximize resulting bandwidth without peaking. printed-circuit layout as with any high-frequency device, good pcb layout is necessary for optimum performance. ground-plane con- struction is highly recommended, as is good power supply bypassing. a 1f?10f tantalum capacitor is recommended in parallel with a 0.01 f ceramic capaci- tor. all lead lengths should be as short as possible, and all bypass capacitors should be as close to the device pins as possible. parasitic capacitances should be kept to an absolute minimum at both inputs and at the output. resistor values should be kept under 1000 w to 2000 w because of the rc time constants associated with the parasitic capacitance. metal-film and carbon resistors are both acceptable, use of wire-wound resistors is not recommended because of parasitic inductance. simi- larly, capacitors should be low-inductance for best performance. if possible, solder the el2074c directly to the pc board without a socket. even high quality sockets add parasitic capacitance and inductance which can potentially degrade performance. because of the degra- dation of ac performance due to parasitics, the use of surface-mount components (resistors, capacitors, etc.) is also recommended.
10 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c el2074c macromodel * * connections: input * | -input * | | +vsupply * | | | -vsupply * | | | | output * | | | | | .subckt m2074 3 2 7 4 6 * *input stage * ie 37 4 1 ma r6 36 37 125 r7 38 37 125 rc1 7 30 200 rc2 7 39 200 q1 30 3 36 qn q2 39 2 38 qna ediff 33 0 39 30 1 rdiff 33 0 1 meg * * compensation section * ga 0 34 33 0 2m rh 34 0 500k ch 34 0 0.8 pf rc 34 40 50 cc 40 0 0.05 pf * * poles * ep 41 0 40 0 1 rpa 41 42 150 cpa 42 0 0.5 pf rpb 42 43 50 cpb 43 0 0.5 pf * * output stage * ios1 7 50 3.0 ma ios2 51 4 3.0 ma q3 4 43 50 qp q4 7 43 51 qn q5 7 50 52 qn q6 4 51 53 qp ros1 52 6 2 ros2 6 53 2 * power supply current * ips 7 4 11.4 ma * models * .model qna npn(is800e-18 bf170 tf0.2 ns) .model qn npn(is810e-18 bf200 tf0.2 ns) .model qp pnp(is800e-18 bf200 tf0.2 ns) .ends
11 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c el2074c macromodel
12 el2074c 400mhz gbwp gain-of-2 stable operational amplifier e l 2 0 7 4 c general disclaimer specifications contained in this data sheet are in effect as of the publication date shown. elantec, inc. reserves the right to make changes in the cir- cuitry or specifications contained herein at any time without notice. elantec, inc. assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. warning - life support policy elantec, inc. products are not authorized for and should not be used within life support systems without the specific written consent of elantec, inc. life support systems are equipment intended to sup- port or sustain life and whose failure to perform when properly used in accordance with instructions provided can be reasonably expected to result in significant personal injury or death. users con- templating application of elantec, inc. products in life support systems are requested to contact elantec, inc. factory headquarters to establish suitable terms & conditions for these applications. elan- tec, inc.?s warranty is limited to replacement of defective components and does not cover injury to persons or property or other consequential damages. s e p t e m b e r 2 6 , 2 0 0 1 printed in u.s.a. elantec semiconductor, inc. 675 trade zone blvd. milpitas, ca 95035 telephone: (408) 945-1323 (888) elantec fax: (408) 945-9305 european office: +44-118-977-6020 japan technical center: +81-45-682-5820


▲Up To Search▲   

 
Price & Availability of EL2074CS-T7

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X